Durga Enterprises

Descriptions of Panasonic MCDJT3220 provided by its distributors.

• The Mitsubishi Q64DAN is a 4-channel analog output module designed for the MELSEC-Q Series PLCs. It provides precise control over analog signals, making it suitable for applications such as temperature regulation, valve control, and other processes requiring analog output.​

   

   

• Mitsubishi Servo Drive MR-J2S 100W MR-J2S-10A
• Theinclusion of a high-resolution encoder ensures high performance and stability at low
• Motor sizes are the same as previous products and wiring is compatible
• The application of a high-performance CPU has enhanced response significantly. Speed loop frequency response is im- proved to 550Hz or
• The MR-J2-Super series are the best choice for use in high-speed positioning applications.
• The absolute positioning method, which does not require home position return, can be used by adding a battery to the servo amplifier. The servo motor does not need to be replaced
• A completely synchronized system can be made using SSCNET utilizing high-speed serial communication with cycle times of up to 0.888ms be- tween controller and amplifier. Such a system will provide high levels of reliability with high levels of performance
• An absolute system can be made by simply adding a battery to the Ser- vo amplifier
• An absolute system can be made by simply adding a battery to the Ser- vo

• Before wiring or inspection, turn off the power and wait for 15 minutes or more until the charge lamp turns off. Then, confirm that the voltage between P and N is safe with voltage tester and others. Otherwise, an electric shock may occur. In addition, always confirm from the front of the servo amplifier, whether the charge lamp is off or not.
• Connect the servo amplifier and servo motor to ground.
• Any person who is involved in wiring and inspection should be fully competent to do the work.
• Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, you may get an electric shock.
• Operate the switches with dry hand to prevent an electric shock.
• The cables should not be damaged, stressed, loaded, or pinched. Otherwise, you may get an electric shock.
• During power-on or operation, do not open the front cover of the servo amplifier. You may get an electric shock.
• Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging area are exposed and you may get an electric shock.
• Except for wiring or periodic inspection, do not remove the front cover even of the servo amplifier if the power is off. The servo amplifier is charged and you may get an electric shock.

• Install the servo amplifier, servo motor and regenerative resistor on incombustible material. Installing them directly or close to combustibles will lead to a fire.
• Always connect a magnetic contactor (MC) between the main circuit power supply and L1, L2, and L3 of the servo amplifier, and configure the wiring to be able to shut down the power supply on the side of the servo amplifier’s power supply. If a magnetic contactor (MC) is not connected, continuous flow of a large current may cause a fire when the servo amplifier malfunctions.
• When a regenerative resistor is used, use an alarm signal to switch main power off. Otherwise, a regenerative transistor fault or the like may overheat the regenerative resistor, causing a fire.

• MRJ SERIES
• 201475721 
• L43E68
• 1CJ001
• 50/60HZ
• 3PH+1PH200-230V

• Control circuit power supply input Allowable voltage variation : Single phase AC 170 V to 264 V

• Control circuit power supply input Allowable frequency variation : Within ± 5%

• Control circuit power supply input power consumption [W] : 30

• Interface power supply : DC 24 V ± 10% (Required current capacity: 0.3 A (including CN 8 connector signal))

• control method : Sine wave PWM control · Current control system

• Allowable regenerative power Regenerative resistor with built-in servo amplifier [W] : 20

Additional Information:

• Delivery Time: 10-15 Days

• Before wiring or inspection, turn off the power and wait for 15 minutes or more until the charge lamp turns off. Then, confirm that the voltage between P and N is safe with voltage tester and others. Otherwise, an electric shock may occur. In addition, always confirm from the front of the servo amplifier, whether the charge lamp is off or not.
• Connect the servo amplifier and servo motor to ground.
• Any person who is involved in wiring and inspection should be fully competent to do the work.
• Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, you may get an electric shock.
• Operate the switches with dry hand to prevent an electric shock.
• The cables should not be damaged, stressed, loaded, or pinched. Otherwise, you may get an electric shock.
• During power-on or operation, do not open the front cover of the servo amplifier. You may get an electric shock.
• Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging area are exposed and you may get an electric shock.
• Except for wiring or periodic inspection, do not remove the front cover even of the servo amplifier if the power is off. The servo amplifier is charged and you may get an electric shock.

• Install the servo amplifier, servo motor and regenerative resistor on incombustible material. Installing them directly or close to combustibles will lead to a fire.
• Always connect a magnetic contactor (MC) between the main circuit power supply and L1, L2, and L3 of the servo amplifier, and configure the wiring to be able to shut down the power supply on the side of the servo amplifier’s power supply. If a magnetic contactor (MC) is not connected, continuous flow of a large current may cause a fire when the servo amplifier malfunctions.
• When a regenerative resistor is used, use an alarm signal to switch main power off. Otherwise, a regenerative transistor fault or the like may overheat the regenerative resistor, causing a fire.

Additional Information:

• Delivery Time: 7-10 Days

• Before wiring or inspection, turn off the power and wait for 15 minutes or more until the charge lamp turns off. Then, confirm that the voltage between P and N is safe with voltage tester and others. Otherwise, an electric shock may occur. In addition, always confirm from the front of the servo amplifier, whether the charge lamp is off or not.
• Connect the servo amplifier and servo motor to ground.
• Any person who is involved in wiring and inspection should be fully competent to do the work.
• Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, you may get an electric shock.
• Operate the switches with dry hand to prevent an electric shock.
• The cables should not be damaged, stressed, loaded, or pinched. Otherwise, you may get an electric shock.
• During power-on or operation, do not open the front cover of the servo amplifier. You may get an electric shock.
• Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging area are exposed and you may get an electric shock.
• Except for wiring or periodic inspection, do not remove the front cover even of the servo amplifier if the power is off. The servo amplifier is charged and you may get an electric shock.

• Install the servo amplifier, servo motor and regenerative resistor on incombustible material. Installing them directly or close to combustibles will lead to a fire.
• Always connect a magnetic contactor (MC) between the main circuit power supply and L1, L2, and L3 of the servo amplifier, and configure the wiring to be able to shut down the power supply on the side of the servo amplifier’s power supply. If a magnetic contactor (MC) is not connected, continuous flow of a large current may cause a fire when the servo amplifier malfunctions.
• When a regenerative resistor is used, use an alarm signal to switch main power off. Otherwise, a regenerative transistor fault or the like may overheat the regenerative resistor, causing a fire.

• Built-in Dynamic Brake: Provides rapid stopping and safety during power-off or faults
• Safety Function: Includes Safe Torque Off (STO) function, compliant with IEC/EN 61800-5-2
• Command Interface: Generic interface for flexible connectivity
• High-Precision Control: Supports advanced motion control with high-speed response

• Before wiring or inspection, turn off the power and wait for 15 minutes or more until the charge lamp turns off. Then, confirm that the voltage between P and N is safe with voltage tester and others. Otherwise, an electric shock may occur. In addition, always confirm from the front of the servo amplifier, whether the charge lamp is off or not.
• Connect the servo amplifier and servo motor to ground.
• Any person who is involved in wiring and inspection should be fully competent to do the work.
• Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, you may get an electric shock.
• Operate the switches with dry hand to prevent an electric shock.
• The cables should not be damaged, stressed, loaded, or pinched. Otherwise, you may get an electric shock.
• During power-on or operation, do not open the front cover of the servo amplifier. You may get an electric shock.
• Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging area are exposed and you may get an electric shock.
• Except for wiring or periodic inspection, do not remove the front cover even of the servo amplifier if the power is off. The servo amplifier is charged and you may get an electric shock.

• Install the servo amplifier, servo motor and regenerative resistor on incombustible material. Installing them directly or close to combustibles will lead to a fire.
• Always connect a magnetic contactor (MC) between the main circuit power supply and L1, L2, and L3 of the servo amplifier, and configure the wiring to be able to shut down the power supply on the side of the servo amplifier’s power supply. If a magnetic contactor (MC) is not connected, continuous flow of a large current may cause a fire when the servo amplifier malfunctions.
• When a regenerative resistor is used, use an alarm signal to switch main power off. Otherwise, a regenerative transistor fault or the like may overheat the regenerative resistor, causing a fire.

• S057

• Before wiring or inspection, turn off the power and wait for 15 minutes or more (20 minutes or for drive unit 30kW or more) until the charge lamp turns off. Then, confirm that the voltage between P( ) and N( ) (L and L for drive unit 30kW or more) is safe with a voltage tester and others. Otherwise, an electric shock may occur. In addition, always confirm from the front of the servo amplifier (converter unit), whether the charge lamp is off or not.
• Connect the converter unit, servo amplifier (drive unit) and servo motor to ground.
• Any person who is involved in wiring and inspection should be fully competent to do the work.
• Do not attempt to wire the converter unit, servo amplifier (drive unit) and servo motor until they have been installed. Otherwise, you may get an electric shock.
• Operate the switches with dry hand to prevent an electric shock.
• The cables should not be damaged, stressed loaded, or pinched. Otherwise, you may get an electric
• shock.
• During power-on or operation, do not open the front cover. You may get an electric shock.
• Do not operate the converter unit and servo amplifier (drive unit) with the front cover removed. Highvoltage terminals and charging area are exposed and you may get an electric shock.
• Except for wiring or periodic inspection, do not remove the front cover even if the power is off. The servo
• amplifier (drive unit) is charged and you may get an electric shock.

• Only the voltage specified in the instruction manual should be applied to each terminal, Otherwise, a burst, damage, etc. may occur.
• Connect the terminals correctly to prevent a burst, damage, etc.
• Ensure that polarity ( , ) is correct. Otherwise, a burst, damage, etc. may occur.
• Take safety measures, e.g. provide covers, to prevent accidental contact of hands and parts (cables, etc.) with the converter unit and servo amplifier (drive unit) heat sink, regenerative resistor, servo motor, etc. since they may be hot while power is on or for some time after power-off. Their temperatures may be high and you may get burnt or a parts may damaged.
• During operation, never touch the rotating parts of the servo motor. Doing so can cause injury. 

• Before wiring or inspection, turn off the power and wait for 15 minutes or more until the charge lamp turns off. Then, confirm that the voltage between P and N is safe with voltage tester and others. Otherwise, an electric shock may occur. In addition, always confirm from the front of the servo amplifier, whether the charge lamp is off or not.
• Connect the servo amplifier and servo motor to ground.
• Any person who is involved in wiring and inspection should be fully competent to do the work.
• Do not attempt to wire the servo amplifier and servo motor until they have been installed. Otherwise, you may get an electric shock.
• Operate the switches with dry hand to prevent an electric shock.
• The cables should not be damaged, stressed, loaded, or pinched. Otherwise, you may get an electric shock.
• During power-on or operation, do not open the front cover of the servo amplifier. You may get an electric shock.
• Do not operate the servo amplifier with the front cover removed. High-voltage terminals and charging area are exposed and you may get an electric shock.
• Except for wiring or periodic inspection, do not remove the front cover even of the servo amplifier if the power is off. The servo amplifier is charged and you may get an electric shock.

• Install the servo amplifier, servo motor and regenerative resistor on incombustible material. Installing them directly or close to combustibles will lead to a fire.
• Always connect a magnetic contactor (MC) between the main circuit power supply and L1, L2, and L3 of the servo amplifier, and configure the wiring to be able to shut down the power supply on the side of the servo amplifier’s power supply. If a magnetic contactor (MC) is not connected, continuous flow of a large current may cause a fire when the servo amplifier malfunctions.
• When a regenerative resistor is used, use an alarm signal to switch main power off. Otherwise, a regenerative transistor fault or the like may overheat the regenerative resistor, causing a fire.